Henry Mini Bolt .22

The serial number is located on the top of the receiver. Record this number in this manual for future reference.

ALWAYS USE THE CORRECT AMMUNITION FOR YOUR PARTICULAR FIREARM. Henry Repeating Arms Firearms are designed to function with a variety of brands and types of factory manufactured ammunition in the appropriate caliber, but not all ammunition produces the same result. Be sure the only ammunition you carry correctly matches the gauge or caliber you are shooting. Never use non-standard, reloaded, or “hand-loaded” ammunition which has not been subjected to internal ballistic pressure testing. Henry RAC recommends that after you read and understand this manual, you go to the range and fire different ammunition which is appropriate to the caliber of your firearm. Once you find the ammunition which functions best, keep using it.

This firearm is designated with an easy to operate manual thumb safety to teach safe gun handling practices.

To activate or turn the safety on, move the safety switch ON by moving the safety rearward, covering the red dot.

To turn the safety off, push the safety forward into the OFF position, exposing the red dot. If you do not have a full understanding of how the safety system works, please call us immediately at 201-858-4400 and ask for technical assistance.

Before using your firearm for the first time, it should be cleaned. (See the cleaning instructions.) Your firearm was treated at the factory with either a preservative or oil to protect it against corrosion during shipping and storage. Preservative and oil should be wiped from the bore, chamber and exposed areas using a clean swab or patch before using the firearm.

Purchase cleaning supplies that are specifically designated for your type and caliber of firearm. Many suppliers offer these in kit form for your convenience. Follow the instructions provided. Whenever your firearm has been exposed to sand, dust, extreme humidity, water or other adverse conditions, it should be cleaned and lubricated.

OPEN THE ACTION

In order to open the action, you must pull the safety rearward into the ON position, covering the red dot. Next, lift the bolt handle upwards until it cannot go any further (it will be aligned with the slot in the receiver) and pull the bolt rearward until it stops.

LOAD THE RIFLE

With the safety ON, open the bolt as described above. Place a cartridge into the chamber, ensuring cartridge is fully seated into the breech of the barrel. Next, slide bolt forward until you hear the click of the extractor engaging the rim of the cartridge case. Now lower the bolt handle until it stops in the downward position. The bolt is now closed. Even though the bolt is closed, the gun will not fire because you have not yet cocked the cocking knob.

THE CAPACITY IS 1 ROUND.

With the safety in the ON position, point the rifle in a safe direction. Grasp the cocking knob very firmly and pull the cocking knob fully rearward until the sear locks into the firing pin. You will feel and hear this engagement. The cocking knob is now fully rearward and locked into position.

WARNING – THE RIFLE IS NOW READY TO FIRE.

If you intend to fire the rifle, point the barrel in a safe direction. Move the safety to the “OFF” position by pushing the safety forward to the fire position, exposing the red dot. Now you are ready to fire the rifle by depressing the trigger. Only when you intend to fire the rifle should you cock the rifle and only when you intend fire the rifle should the safety be in the “OFF” position.

It is suggested that you do NOT dry fire this rifle. Repeated dry firing of a rimfire can eventually peen the edge of the chamber, making it difficult to load and extract cartridges.

This practice should be used when either de-cocking or unloading a spent/live round. You must use EXTREME CAUTION when removing a live cartridge from the chamber. If you intend to remove a live cartridge from the chamber, first point the gun in a safe direction. Then, put the Safety in the “OFF” position, exposing the red dot.

To de-cock your rifle, grasp the cocking knob very firmly with one hand, and pull it back further. There will be some resistance. During this process your hand should remain firmly on the cocking knob, holding it back at all times. As you are holding the cocking knob back, at the same time, use your other hand and depress the trigger. Depressing the trigger will disengage the cocking knob/firing pin.

Move the cocking knob forward slightly and then take your finger off the trigger. Keep your hand firmly on the cocking knob and proceed very slowly to bring the cocking knob forward into a resting position. You can now remove your hand from the cocking knob.

To unload your rifle, rotate the bolt handle upward and pull the bolt rearward to open the action. You will now be able to remove the live cartridge from the action.

Instructions on installation of the scope mounts (not included) is provided in the packaging. All Henry Scope Mounts accept Weaver style detachable 1″ top mount rings (rings not included).

Your H005 Mini Bolt is equipped with high visibility Williams Fire Sights using a three-dot sight pattern with a fixed red fiber-optic on the front blade and two green fiber-optic dots on the fully adjustable rear sight.

High or Low (Elevation Adjustment)

Your rifle can be adjusted to shoot higher, by turning the set screw on the REAR SIGHT counter clockwise. In order to shoot lower, turn the set screw (clockwise).

Left or Right (Windage Adjustment)

To adjust for your windage (left/right), loosen the set screw nearest the front of the rear sight. In order to move the point of impact to the left, move the rear sight to the left and vice-versa. Make sure to re-tighten the set screw when your adjustments are completed.

NEVER USE YOUR FIREARM IF IT FAILS TO FUNCTION PROPERLY, AND NEVER FORCE A JAMMED ACTION. Forcing the action could make the round explode, causing serious injury, possible death, or severe damage to your firearm or other property.

FAILURE TO FIRE. A misfire occurs when the firing pin strikes the primer and it does not fire.  IF THE FIREARM FAILS TO FIRE DO NOT PUT IT DOWN OR OPEN THE ACTION. ALWAYS HOLD THE FIREARM, KEEPING IT POINTED IN A SAFE DIRECTION AND WAIT 30 SECONDS. IF A HANGFIRE (SLOW IGNITION) HAS OCCURRED, THE ROUND WILL FIRE WITHIN 30 SECONDS.

If the round does not fire, remove the ammunition, eject the round and examine the shell. If the firing pin indent on the primer is light or non-existent, have the firearm examined by a competent gunsmith before firing again. If the firing pin indent on the primer appears normal (in comparison with similar previously fired rounds) assume you have faulty ammunition.  Segregate the misfired round from other live ammunition and empty cases, reload, and carry on firing.

FAILURE TO EXTRACT (FTE). This is when the firearm discharges the round and fails to extract the spent round from the chamber. This could happen because of a bad extractor or bad/damaged casings.

FAILURE TO FEED (FTF). This is simply when the firearm fails to feed another round into the chamber. Put the lever in the open position and clear the ejection port.

Note: The ejection port should face the ground; this will allow the round to easily fall out (gravity is your friend here). This will work for both left and right handed shooters.

WARNING: BEFORE PERFORMING CLEANING PROCEDURES, MAKE SURE THE HAMMER IS IN THE FIRED-DOWN POSITION, WHICH ALLOWS YOUR SAFETY TO FUNCTION AS DESIGNED. OPEN THE ACTION AND MAKE CERTAIN YOUR FIREARM IS COMPLETELY UNLOADED. KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

KEEP ALL AMMUNITION AWAY FROM THE CLEANING AREA. NEVER TEST THE MECHANICAL FUNCTION OF YOUR RIFLE WITH LIVE AMMUNITION. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

NOTICE! It is very important that the bore of your rifle be cleaned thoroughly and promptly after shooting. Do not leave discharged (empty) cases in the chambers for any length of time, as the chemical composition of many cartridges contain moisture which can “sweat” out of the shell and onto the chambers’ surfaces, and possibly cause corrosion and rust.

You should always clean your rifle after firing. If you do not fire many rounds, you can simply use a .22 caliber rifle cleaning kit. Regular cleaning is important in order for your gun to operate efficiently and safely. Taking proper care of it will also maintain its value and extend its life.
Before cleaning your rifle, verify it is unloaded. Always point the barrel in a safe direction and treat every firearm as if it is loaded.

NOTICE! DO NOT ATTEMPT TO TAKE YOUR FIREARM APART FURTHER THAN EXPLAINED IN THIS MANUAL. Your firearm is a specialized, finely fitted mechanism. You may permanently damage it by attempting to disassemble the inner mechanisms. If further disassembly for service or cleaning is required, take your firearm to a qualified gunsmith.

To clean remove the bolt from the rifle, place the SAFETY in the “OFF” position, exposing the red dot. Rotate the bolt handle upward and pull rearward on the bolt until it is back as far as it can go. Pull the trigger fully rearward and then pull the bolt rearward. The bolt will be able to slide out of the receiver. Clean the bolt thoroughly with gun cleaning solvent.

ALWAYS CLEAN FROM THE NATURAL DIRECTION OF THE BULLET. When you fire your gun, powder residue and dirt will accumulate in the barrel. If you run a brush or patch from the muzzle end you will push this dirt, residue, and moisture into the chamber and receiver. This is a major cause of stuck cases or problems. If you push or pull a brush back toward the chamber, you will notice the brush will throw the debris from the bore back into the chamber. You do not have to disassemble this firearm in order to clean it sufficiently and to keep it operating properly.

USE A CLEAN PATCH SURFACE EACH TIME YOU GO DOWN THE BARREL. When you are using your firearm you will get abrasive dirt in the bore. A patch with an approved firearm cleaning solvent can be used to remove deposits from chamber and bore. Reusing a soiled patch or cleaning from muzzle to breech will deposit dirt and powder residue into the action.

NEVER GO BACK AND FORTH REVERSING THE BRUSH. This will bend the bristles on the brush. This is the equivalent of bending a wire back and forth until it breaks. You will always ruin a brush if you reverse it while in the bore.

USE ONLY A FEW DROPS OF SOLVENT/LUBRICANT OIL. Use only the amount of solvent that the patch will absorb. If you use too much, the solvent or oil will drip down into the trigger mechanism.

CENTER THE TOP AND ROD. BE CAREFUL NOT TO LET EITHER RUB THE BORE. All firearms record their history. This is the reason most people look down the barrel of a firearm. An experienced eye can tell the method of cleaning, the number of shots, and the gun maintenance applied to the firearm. Many marks are caused by people who carelessly let the tip or rod rub the inside the barrel.

NEVER RUN A BRUSH IN THE BARREL FIRST. This will damage the firearm. The brush will pick up dirt, moisture or powder residue and deposit it into the chamber or receiver. Never dip a brush in solvent. The solvent at the brush core will collect dirt and drop it into the receiver and chamber. Remember – Rust is neglect. Make sure all exposed metal surfaces are coated with a film of oil. After being subjected to damp weather, thoroughly wipe the bore and metal surfaces. Then apply a new film of oil. If exposed to a soaking rain, snow or salt spray, a more thorough cleaning and oiling may be necessary. Wipe the bolt clean of any debris with solvent and a patch or small rag. Spray the bolt with some gun oil.

To reinstall the bolt back into the rifle, place the SAFETY in the “OFF” position. Pull the trigger and hold this position. Place the bolt in the receiver, aligning the bolt handle with the slot in the receiver. Push the bolt forward into the receiver until it is flush against the barrel. Rotate the bolt handle downward to lock into position.

When storing your firearm, do not encase it in anything that will attract or hold moisture, for example, leather or heavy cloth. Also, do not store firearms with a plug inserted in the barrel because this can be a contributing factor to moisture accumulation.

If your firearm is to be stored for an extended period, the bore, chamber and internal surfaces should be oiled with a high-quality lubricating oil or preservative intended for firearms. The external parts; receiver, bolt and barrel should be coated with an anti-rust oil.

Before using your firearm again, be sure to clean it. Every time you clean your firearm, check it for signs of wear. If wear is noted, do not use the firearm, have it checked by a qualified gunsmith.

Make sure your firearm is in good mechanical condition before firing it. Periodically have your firearm checked for signs of erosion, cracking, or wear by the factory or a factory certified gunsmith.

NEVER LOCK A LOADED FIREARM AND NEVER LOAD A LOCKED FIREARM!

ALWAYS CHECK TO MAKE SURE YOUR FIREARM IS NOT LOADED BEFORE CLEANING, STORING, TRANSPORTING IT, LAYING IT DOWN, OR HANDING IT TO ANOTHER PERSON so that it cannot be fired when it is unsafe to do so.

ALWAYS KEEP AND STORE YOUR FIREARM AND AMMUNITION IN SEPARATE, LOCKED LOCATIONS, OUT OF REACH AND SIGHT OF CHILDREN AND UNTRAINED PERSONS. Safe and secure storage of your firearm and ammunition are your responsibility.

NEVER LEAVE THE KEY TO THE LOCK FOR YOUR FIREARM WITH THE STORED FIREARM!

NEVER ASSUME THAT A “HIDING” PLACE IS A SECURE STORAGE METHOD.  Others may be aware of your storage location or come upon it by chance. It is your personal responsibility to use common sense when storing your firearm and ammunition and to always make sure they are not accessible to children or other unauthorized persons.

NOTE: Do not store your firearm in an air-tight container, and do not seal or attempt to seal the barrel to exclude dust, as the internal steel surface is more likely to rust or corrode by doing this.

BEWARE OF BARREL OBSTRUCTIONS. Be sure the barrel is clear of obstructions before shooting. Mud, water, snow or other objects may inadvertently lodge in the barrel bore. A small obstruction can cause a dangerous increase in pressure and may damage your firearm and cause injury to yourself and others.

BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN YOUR FIREARM IS COMPLETELY UNLOADED. After assuring yourself that the firearm is completely unloaded, open the action and look through the barrel to be sure it is clear of obstructions. If an obstruction is seen, no matter how small it may be, clean the bore with a cleaning cord or a patch as described in the CLEANING section of this owner’s manual.

BE SURE ALL ACCESSORIES, SUCH AS SLINGS, SCOPES AND OTHER ACCESSORIES ARE COMPATIBLE WITH YOUR PARTICULAR FIREARM AND THAT THE ACCESSORIES DO NOT INTERFERE WITH ITS SAFE OPERATION.

It is your responsibility to understand and follow all of the instructions in the safety manual that accompanied your firearm, as well as those which may be supplied with your ammunition and any accessory.

NEVER DISASSEMBLE YOUR FIREARM BEYOND THE FIELD STRIPPING PROCEDURE OUTLINED IN THIS MANUAL. Improper disassembly or reassembly of your firearm may be dangerous and can lead to serious injury or death.

NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THE INTERNAL COMPONENTS OF YOUR FIREARM UNLESS SPECIFICALLY INSTRUCTED TO DO SO IN THIS MANUAL.  Improper manipulation of any other internal component may affect the safety and reliability of your firearm and may cause serious injury or death.

NEVER ALLOW ANY ALTERATION OR REPLACEMENT OF PARTS IN YOUR FIREARM UNLESS PERFORMED BY A QUALIFIED GUNSMITH USING AUTHORIZED PARTS. If you do otherwise, improper functioning of your firearm may occur and serious injury or death and damage to property may result.